START here

Pros and cons of 1x groupsets/systems

The cycling industry, mostly for marketing reasons, moves towards an ever-increasing “number of speeds” at the back. However, there is also a trend of having fewer front chainrings. First, the triples were extinct from high-end groupsets of big manufacturers, then they came for the doubles… 🙂 

Today’s modern thing is the 1x – bicycle groupsets with only one front chainring. SRAM was the first to announce “the death of the front derailleur” when they made the first 1x groupset, while other manufacturers joined the race. This post will give an objective overview of 1x system pros and cons, compared to 2x (double), and 3x (triple) systems, so you could easily decide whether 1x is an optimal choice for You.

1X, 2X, and 3X cranks
1X, 2X, and 3X cranks

When “weighing” pros and cons, it is important to note that, while they are objective, their significance depends on particular cyclist’s priorities and riding conditions, even preferences, budget etc. Likewise, the number of pros and cons is irrelevant – it matters how much they affect performance, which entirely depends on riding conditions, as will be explained. In those terms, at the end of this post I’ll give an overview of some typical cases and what I think is the optimal choice for each, based on my knowledge and experience. Still, it’s best to weigh the pros and cons personally and decide for and by yourself what works for you.

Table Of Contents (TOC):

  1. Pros of 1x systems
  2. Cons of 1x systems
  3. Further differences
    3.1. Large gear ratio “jumps”
    3.2. Overlapped gear ratios
    3.3. More rear sprockets = weaker wheel
    3.4. Ground clearance
    3.5. Total number of teeth for a given gear ratio
    3.6. Chain line and cross chaining
  4. Typical cases – when is which system an optimal choice


1. Pros of 1x systems

  • Lower overall groupset mass (“weight”) – there’s no front shifter and derailleur, only one front chainring, no front shifter cables/housing.
  • Simpler shifting – only one (rear) shifter, up-down, faster-slower.
  • Better overall aerodynamics – the effect is very, very small, but for time-trial, rear derailleur is “tucked” behind riders’s legs, while extra front chainrings do create some, slight additional air drag. Yes, it sounds almost ridiculous, but for a TT trial, it might just make a split-second difference (all else having been made as aero as possible – helmet, clothes, frame, wheels, riding posture…).
  • No problems with the front derailleur – when riding through sticky mud, it can pile up on the front derailleur, creating drag on the rear wheel and also hampering front derailleur operation. Rear derailleur is away from the tyre and less likely to get soaked in mud.
  • Gives more freedom in frame design – important for full suspension off road bicycles. This leaves more room for wider tyres and rear suspension connecting linkages.
  • Less chain drop on off-road riding – while well set up multi-chainring system doesn’t drop the chain every day, it can be said that modern 1x systems are a bit more robust when it comes to not dropping the chain when jumping over bumps (and shifting).
  • One fewer lever at the bars – with no front shifter, there’s more room on the bars for other gadgets, such as suspension and dropper seatpost lockout levers, which are used on many modern MTBs.

– T.O.C. –


2. Cons of 1x systems

  • Smaller gearing ratio span – 2x and 3x systems (doubles and triples) generally give a larger gearing range, that is the difference between the “slowest” and the “fastest” gear.
  • Greater adjacent gearing ratio differences (gaps) – in order to get somewhat usable gearing ratio range, tooth count difference of adjacent rear sprockets needs to be relatively high, since the “tool” for getting a wider gear range (front derailleur and multiple chainrings) is thrown away.
  • Necessity for an outrageous number of rear sprockets – for the two reasons stated above, 1x systems require 11, 12, even 13 sprockets at the rear to get the sufficient gearing ratio range and “tightness” that is otherwise easily achieved using a 3×7 (7 sprocket) system.
  • Shorter chain and sprocket lifetime – will be explained later.
  • Higher price – generally, a good quality 1x groupset costs more than a 2x, or 3x system of similar quality.
  • Greater drivetrain mechanical losses – because of more severe chain angle (cross-chaining) and fewer chainring teeth in some gear combinations.

– T.O.C. –


3. Further differences

3.1. Large gear ratio “jumps”

Systems with multiple front chainrings allow for large changes in gear ratio by doing only one front shift. With 1x systems, this is not present.

With modern “compact” (50-34 toothed) double cranks this can be a problem. Especially if using common 11-28 cassettes (and the like). For riding on flats, 50 is often too large, while 34 is too small. Rider ends up riding severely cross chained most of the time.

With standard doubles (53-39 for road, or 26-36 for MTB), this is not a problem. With triples even less so. There you can usually find an optimal chainring for climbs, flats and downhills, without much cross chaining. In this situation, greater gear ratio change when shifting up front is often beneficial. When starting going up a hill, one front shift gives a significantly “easier” gearing, while fine tuning can be achieved during the climb with rear shifts. Same goes for reaching a hill top – one front shift puts you in a flat/downhill gearing range rather quickly.

So, large “jumps” are not always a bad thing, as some advocates of 1x systems claim.

– T.O.C. –

3.2. Overlapped gear ratios

Often used argument in favour of 1x systems is that “double and triple systems have a lot of double (overlapped) gears, with only about 10-15 really different gear ratios).” This is used in a context that, for example, 2×10 doesn’t offer 20 different gear ratios as if it’s some kind of fraud.

Modern “compact” double cranks, with their large difference in chainring tooth count have very few overlapped gears, but that precisely is their main flaw, as explained in chapter 3.1. They do give a wider gear ratio range, but at the cost of more cross chaining and less practical shifting. Trying to emulate a triple with only two chainrings.

Standard doubles and triples have more overlapped gear ratios. For example a combination of 53 teeth up front and 19 teeth at the rear, gives approximately the same gear ratio as 39-14 combination. If a hill climb is approached, one can ride 39 up front, then make smaller adjustments by shifting at the rear as the climb starts. If riding on a flat, or expecting a downhill, one can use the big ring up front (53), making smaller adjustments with rear shifts. The lack of these overlapped gears is the main nuisance people have with compact doubles.

1x systems have a slight advantage here – no need for planning, or thinking ahead, just shifting up and down. Price paid for that are the 1x systems cons noted in this post.

– T.O.C. –

3.3. More rear sprockets = weaker wheel

Sketch 1 is used to demonstrate what I mean:

Wheel dish difference of a 7 and 12 speed sprocket freehub. Sketch 1
Wheel dish difference of a 7 and 12 speed sprocket freehub.
Sketch 1

The sketch is exaggerated to show what the problem is. Angle that right hand spokes make (A and B). Cassette with more sprockets ends up taking more space, being wider and requires either a wider overall hub (which is limited for most bikes), or weaker wheel due to very sharp angle of right hand spokes. Such wheels can’t take nearly as much lateral load coming from the right hand side. Also, spoke tension differences between left and right hand side spokes are huge, which makes other problems, mostly resulting in a wheel that is less strong and less durable.

7 speeds at the rear has been phased out by manufacturers – who would want a strong, long lasting wheel with cheap components? Not the manufacturers.

Hubs for 8 to 10 speeds (and 11 speed MTB, but not road) have slightly worse right hand spoke angle.

12 speed hubs (and 11 speed road hubs) are even worse.

All this while modern hubs for hard off road riding conditions are made up to 157 mm width! Which makes frame design very difficult, since rear chainstays have to be wide, without pedals (rider’s legs) being too widely placed and without hitting the chainstays at the same time.

1x systems can’t provide useful gear ratio range or “tightness” without at least 11 sprockets – preferably 12, 13… 14? Draw your own conclusion.

– T.O.C. –

3.4. Ground clearance

Same maximum gear ratio can be achieved using a 36 tooth chainring and 12 tooth sprocket, as with a 30-10 combination. Since 30 T chainring has a smaller diameter, ground clearance of such bicycle will be greater than of the one using a 36 T chainring. Where that is important, this is a logical choice (off road). It needs to be said that old MTBs had smaller 26″ wheels and triple chainrings and still got everywhere – now they use standard 28″ wheels (labelled 29″ when placed on a MTB) and clearance has become a problem somehow?

– T.O.C. –

3.5. Total number of teeth for a given gear ratio

In addition to the example from the previous chapter, another one would be that achieving lowest gear ratio of a 30-45 combination would require a 54 toothed largest rear sprocket if used with a 36 toothed cranks. This explains why 1x drivetrains have required having a smallest sprocket of only 10 (or even fewer) teeth. so that a decent top and lowest gear ratio can be achieved without outrageously large sprockets (well, 40+ teeth is outrageously large if you will, but it’s still below 50 teeth).

In the previous chapter, (questionable?) advantage of using 30-10 combination over 36-12 combination way of achieving the same gear ratio was explained (more clearance). What is the (unquestionable) downside? More mechanical losses and faster chain and chainring wear. When a chain is bent over a chainring that is too small (in these terms anything below 13 teeth is very small), there are more mechanical losses due to increased friction and chainring and chain wear is increased, because 1, or 2 teeth carry all the load.

This can be considered to be a flaw of 1x systems.

– T.O.C. –

3.6. Chain line and cross chaining

When advertising 1x systems, one of arguments is also there is “no worrying about cross chaining”. With double and triple setups it is possible to severely cross chain – if using an outer most front chainring with two most inner rear sprockets (big-big combination). The same goes for small-small combination. So yes, this should be avoided and thought of when using these systems. However, it can be avoided. With 1x systems, severe chain angle in highest and lowest gear ratio is unavoidable, as shown in sketch 2.

Chain angle in highest and lowest gear ratios. 1x system - top 2x system - bottom Sketch 2
Chain angle in highest and lowest gear ratios.
1x system – top
2x system – bottom
Sketch 2

So it can be said that with 1x systems there’s no “worrying” about cross chaining – you get what you get, whether you like it, or not.

Greater chain angle leads to higher mechanical losses, chain is more likely to start making noise when working and both chain and chainrings will wear faster. If it’s any consolation, 1x cassettes, with the largest sprocket having 40+ teeth are more expensive, at least.  🙂

Update, May 2022:
According to these submitted patents – Shimano pat. US20170167542A1, and SRAM pat. US20170167590A1, it appears that the manufacturers are aware of this poor chainline problem of 1X systems.

Apparently, they are trying to fix the problem by designing a chainring that rotates left-right, so it can follow the line of a badly angled (crossed) chain.

I expect that in 5 to 10 years’ time, manufacturers will “discover” something like a “front derailleur” and “more than one front chainring” (ofcourse, marketing departments will surely come up with some very cool-sounding names for these!). 🙂

– T.O.C. –

4. Typical cases – when is which system an optimal choice

Here I will list some typical cycling use cases/scenarios, with system that I think is an optimal choice. With a brief explanation why. Of course, it is best to choose for yourself.

  • Road bike for sports/recreation riding – 2x systems give a wide gearing range, that is also tight enough, at a relatively modest price.
  • Sport riding off road in lots of mud – this is where 1x makes some sense and could be a good choice, although 2x and 3x systems can also serve well.
  • Loaded touring – triple (3x) without further ado. Triples offer wide gearing range with any old cassette that can be found along the way, allowing for fewer sprockets to be used for a more robust system, allowing the use of friction shifters as well.
  • Grocery/errand  commuting bicycle – cheapest and simplest possible. If your town is flat, single speed is perfect. If not, get the climbing gearing you need, whether it’s a 1×6, 3×8, or some other system. If theft rate is very low, it makes sense going for a higher quality, more durable (and more expensive) bikes and components.

Useful tool for choosing a cassette and/or gearing setup is “on line gear calculator“.

This concludes the list and explanation of pros and cons of 1x systems compared to 2x and 3x ones. I tried to provide all the info objectively as it is. If you have any questions, corrections, or comments, use the section below.


Help BikeGremlin
stay online & independent

This website is educational, free, objective, and not commercial
(sponsors don’t enjoy paying if you mention all the product downsides that you notice 🙂 ).

How much does a WordPress website cost?

If you find this site to be good and helpful,
and if $5 per month is what you can afford to set aside,
please consider supporting my work with a Patreon donation:


patreon.com/bikegremlin

– T.O.C. –

Relja Triple Novović

The existing comments posted under this article (questions and answers) have been moved to this BikeGremlin forum thread:
https://www.bikegremlin.net/threads/pros-and-cons-of-1x-groupsets-systems-article-comments.117/

44 thoughts on “Pros and cons of 1x groupsets/systems”

  1. As above, narrow wide chainring and 9 speed chain and smaller largest cog all combined to solve the problem.

  2. 1. Three mm spacers can help with the chain line. Cheap from Amazon.
    2. Next in cost is new 9 speed chain
    3. Next is a narrow wide chain ring.
    4.A slightly smaller large cog on the cassette, say 36 teeth instead of 42. 36 might work with your current rear derailleur. It did with my project.
    5. Clutch rear derailleur but about $50 or $60.
    Thanks Relja. Your advice worked well for my daughter.

Comments are closed.


Please use the BikeGremlin.net forum for any comments or questions.

If you've found any errors or lacking information in the article(s) - please let me know by commenting on the BikeGremlin forum.
You can comment anonymously (by registering with any name/nickname), but I think it is good to publicly document all the article additions (and especially corrections) - even if their author chooses to remain anonymous.

Skip to content