START here

Bicycle stem size standards

Stem types and sizes explained. 🙂

If you have any questions (or additions and corrections), please use the BikeGremlin forum:
www.bikegremlin.net

Table of contents (T.O.C.):

TL/DR

  1. Introduction
  2. Types of stems
    1.1. Quill stem
    1.2. Threadless stem
  3. Important dimensions and how to measure
    2.1. Handlebar (clamp) attachment diameter
    2.2. Steering column attachment diameter
  4. Stem dimension standards
    3.1. Handlebar clamp dimension standards
    3.2. Steering column attachment dimension standards
    …3.2.1. Threaded stems
    …3.2.2. Threadless stems


TL/DR

There are two major stem types: threadless (“ahead”), and quill stems.

Each stem has two major dimensions: handlebar attachment diameter, and the fork steering column attachment diameter.

In this article I’ve explained what’s what and how to measure it (in case you need to buy a new stem).

– T.O.C. –


0. Introduction

This post explains stem size standards in terms of steering column attachment and handlebar attachment at the opposite end of the stem. Other dimensions, such as stem length and angle will be explained in a separate post.

A tip:
When buying a stem, unless you already have handlebars of a different standard, I recommend you choose a stem with a modern OS (“oversized”) bar attachment diameter (table 1 lists the standard dimensions).

Dimensions and type of steering column attachment depend on your bike’s fork, so that’s a bit harder to “change” – though, if choosing a frame, I recommend you look for one with a 1 1/8″ steering column diameter and a threadless fork – for several reasons.

– T.O.C. –


1. Types of stems

There are two types of stems (in terms of standard attachment dimension): quill (for threaded forks) and threadless (a.k.a. ahead) stems (for threadless forks).


1.1. Quill stem

Quill stem is attached to the steering column by inserting it into the steering column and tightening a bolt on top of the stem, that pulls the quill upwards, making the lower stem diameter wider. Without much going into details and various designs, the basic principle is shown in picture 1.

– T.O.C. –


1.2. Threadless stem

Threadless stems have a slot at the steering column attachment end. It is fastened by sliding it onto the steering column, and then tightening the pinch bolt(s) that hold it fastened.

Threadless ("ahead") stem Picture 2
Threadless (“ahead”) stem
Picture 2

– T.O.C. –


2. Important dimensions and how to measure

Stems are made with various lengths and angles. Picture 2a shows a quill stem with a shorter neck, angled downwards, next to a threadless stem with a longer neck. Lenghts and angles differ and are important when fitting a bicycle to suit a rider. However, in terms of (attachment) standards, important dimensions are the handlebar attachment diameter and steering column attachment diameter.

– T.O.C. –


2.1. Handlebar (clamp) attachment diameter

This dimension is measured practically identically for all the stems. The name says what it is. Measurement method is shown in picture 3.

Picture 3b doesn’t show clearly enough, but the calipers are placed at the inner side of the black part of the stem, just near the slit – there would be no use measuring at the slit itself, of course.

One could also measure the (outer) bar diameter (at the stem attachment point) – if a new stem is sought to match the bars.

– T.O.C. –


2.2. Steering column attachment diameter

For threadless stems, this is measured the same as the handlebar attachment diameter. Picture 4 says it all.

Of course, if a new stem is sought for a fork at hand, then the fork is measured. Picture 5 shows how.


3. Stem dimension standards

After dimensions were defined and their measurement explained, now an overview of the standard dimensions will be given. First table will show bar attachment diameter standard. Second table will show threadless stems for attachment diameters. While the third one will show that for the quill stems.

– T.O.C. –


3.1. Handlebar clamp dimension standards

TABLE 1 
Handlebar attachment diameter – measurement units: mm (inches) Standard name
22.2 (7/8″)for steel bars of old MTB and BMX bikes
23.8 (15/16″)Obsolete British standard common on old British 3-speeds
25Obsolete French standard
25.4 (1″)Standard ISO size, common for bars from the end of the 20th century
26Italian road bike (and bar) standard. Obsolete
27Titan – obsolete standard
31.7 – 31.8 – depending on how manufacturers round down the inch dimension which is (1 1/4″)Modern “oversized” standard
35 (1 3/8″)Easton standard

– T.O.C. –


3.2. Steering column attachment dimension standards

3.2.1. Threaded stems (quill stems)

TABLE 2 
Stem “neck” outer diameter – measurement units: mm (inches) Standard name
21.15 (13/16″)Old American and BMX standard
22Old French standard
22.2 (7/8″)Standard for most threaded forks with an outer diameter of 25.4 mm (1″)
25.4 (1″)Standard for most threaded forks with an outer diameter of 28.6 mm (1 1/8″) – not very common

– T.O.C. –


3.2.2. Threadless stems

TABLE 3 
Steering column outer diameter (and inner diameter for the attachment on the stem)Standard name
measurement units: mm (inches) 
25.4 (1″)One inch standard
28.6 (1 1/8″)1-1/8 inch standard
31.8 (1 1/4″)1-1/4 inch standard
38.1 (1 1/2″)1-1/2 inch standard

Related post – Bicycle handlebar dimension standards:

Bicycle handlebar dimension standards
Bicycle handlebar dimension standards

If you have any questions (or additions and corrections), please use the BikeGremlin forum:
www.bikegremlin.net

– T.O.C. –




Help BikeGremlin
stay online & independent

This website is educational, free, objective, and not commercial
(sponsors don’t enjoy paying if you mention all the product downsides that you notice 🙂 ).

How much does a WordPress website cost?

If you find this site to be good and helpful,
and if $5 per month is what you can afford to set aside,
please consider supporting my work with a Patreon donation:


patreon.com/bikegremlin

The existing comments posted under this article (questions and answers) have been moved to this BikeGremlin forum thread:
https://www.bikegremlin.net/threads/bicycle-stem-size-standards-article-comments.137/

18 thoughts on “Bicycle stem size standards”

  1. I have a bicycle from I believe 1976 and it does not have a 22.2 MM stem but smaller.

    I am uncertain what size I think possibly 16 or 18 mm.

    Sincerely, Christopher I have

  2. A threaded headset is also beneficial for road bike riders who wish to achieve comfort while sporting an upright cycling position when cycling, but the replacement of parts, such as forks and stem tubes, is expensive due to their limited market availability.

Comments are closed.


Please use the BikeGremlin.net forum for any comments or questions.

If you've found any errors or lacking information in the article(s) - please let me know by commenting on the BikeGremlin forum.
You can comment anonymously (by registering with any name/nickname), but I think it is good to publicly document all the article additions (and especially corrections) - even if their author chooses to remain anonymous.

Skip to content