This post explains important facts about bicycle rear derailleurs. From construction and parts, to important characteristics such as chain wrap capacity etc.
Rear derailleurs (often refferd to as RD) are used on bicycles with external gearing and multiple sprockets at the rear hub. They work on a simple, brute force principle: moving the chain sideways, until it slips off a sprocket onto the adjacent one.
This derailleur movement is usually operated via shifters (shifter levers), that are located on the bars (or somewhere at hand). Shifter cable is attached to shifters at one and and at the derailleur at the other end.
It consists of a metal cage and a spring. The spring moves derailleur to one side when the shifter cable is released, while the shifter cable, when pulled, moves it to the opposite side. It also has jockey wheels on a cage, with a spring, used to pull extra chain when changing to different sprocket sizes, so it doesn’t fall off.
There are two ways of rear derailleur attachment:
- Hook type (derailleur has a built in hook).
- Direct mount (frame must have a point for screwing the derailleur onto).
Which one of these derailleur mount types is used, depends on the frame rear dropout type:
The way of mounting each derailleur type is shown in the pictures below:
Most rear derailleurs have a spring pushing them outwards. When shifter cable is released, the derailleur moves outwards, towards the smaller sprockets. When shifter cable is pulled, movement is reversed – towards the wheel, bigger sprockets. This way of functioning is called “high-normal“, or “top-normal“.
“Shimano Rapid Rise“, also called “low-normal” derailleurs work the opposite way: spring pushes them towards the wheel, while pulling shifter cable moves them towards smaller sprockets. Same shifter levers can be used for both standards. If a shifter lever has gear indicator, if a rapid-rise is put instead of standard (or vice-versa, for rapid rise shifter levers), indicator will show “upside-down”. But shifting will work correctly.
Derailleur capacity is a number of tooth difference between front and rear sprockets that the derailleur can compensate. When chain is put on the largest chainring up front and the largest sprocket, the chain needs to be long enough to wrap. Then, when chain is placed on the smallest sprocket at the rear and smallest chainring, there will be a lot of “extra” chain length that rear derailleur pulleys must “gather”, to keep the chain tensioned. These are both extreme combinations, with worst cross chaining, so not recommended in practice.
So manufacturer chain capacity data can be taken with some liberty, if the user is experienced and careful, never using extreme combinations.
Derailleurs come in three sizes: short, medium and long cage. Derailleur capacity is proportional to cage length. For wide range MTB cassettes with three front chainrings, it is practical to have a long cage derailleur. A typical narrow ranged road cassette and two front chainrings will make do with a short cage derailleur.
Shimano notes RDs as: SS (short cage), GS (medium cage) and SGS (long cage).
Example: if a bicycle has a crankset with 48-38-28 teeth, and a cassette that ranges from 11-32 teeth, then a needed RD capacity would be:
(48-28) + (32-11) = 20 + 21 = 41
This would take a long cage RD with over 40 teeth capacity
For a typical road bike setup with 53-39 crankset and a 11-25 cassette:
(53-39) + (25-11) = 14 + 14 = 28
A short cage RD with under 30 tooth capacity would suffice.
Apart from RD capacity, an important characteristic of a RD is the maximum number of teeth of the biggest rear sprocket that RD can handle. For short cage road bike RDs, this is usually about 25, or 28, while long cage MTB ones often enable use of 32, 34, or even more teeth at the cassette.
A series of posts explaining what can be combined with what: Compatibility
MTB rear derailleurs from 6 to 9 speeds, and road RDs from 6 to 10 speeds are interchangeable and compatible. Slight difference in jockey wheel thickness is not a problem – a 6 speed RD will work on any number of speeds – up to 9 with a MTB and up to 10 with a road bike. It is the same ratio of derailleur cage movement per cable movement, so the shifter levers determine the movement and the number of “speeds”.
10 and 11 speed MTB derailleurs, as well as 11 speed road bike derailleur are not interchangeable. Different cable pull ratio and parallelogram movement for each. There are exceptions from these rules, so if some combining (mix-matchin) is planned, it is best to first read the post about bicycle rear derailleur compatibility.
If shifters used are indexed, shifter mechanism determines amount of cable pulled for each gear, with each shifter click. So rear shifter compatibility needs to be accounted for. There is a difference in cable pull ratio for Campagnolo, SRAM and Shimano. That is why a SRAM rear derailleur will not work properly with indexed Shimano shifters (and vice-versa). With friction shifters (those that don’t have a click for each gear), this is not an issue.
So, one could say that if using indexed shifters, they will work as long as the RD is by the same manufacturer as the shifters. Though, apart from Campagnolo and SRAM, most other manufacturers are compatible with Shimano.